2pc Circlip / Snap Ring Pliers Set
165mm Internal and External Pliers
with Straight and 45 / 90 degree Tips
Sizes : 0.8mm | 1.2mm | 1.4mm | 2.0mm

10pc Circlip / Snap Ring Pliers Set
Straight Tips : 0.038 | 0.047 | 0.070 | 0.090
Bent Tips - 0.038 | 0.047 | 0.070 | 0.090
5in. Hook Tool
5in. Pick Tool

Extra Long Circlip / Snap Ring Pliers - 10in. 2pc Set
includes 16 Replacement tips.
Offset tips make it easier to install and remove circlips.
Removable and replaceable tips
with spring ratchet locking mechanism
to hold circlips securely against tension.

4pc Circlip / Snap Ring Pliers Set
13in. / 325mm with Straight and 90 degree Tips
Supplied with fabric case.

Ratchet Hose Clip Pliers
Jaw Range 22 - 55mm
For flat-type hose Clamps in hidden and hard to reach areas.
Fits most ring-type or flat-band hose Clamps.
The Clamps are held open with a ratchet locking mechanism.

7pc Hose Clip Pliers Set
Hose Clip Pliers
Swivel Jaw Spring Wire Clip Pliers
Swivel Jaw Spring Band Clip Pliers
Flat Band Clip Pliers
Angled Flat Band Clip Pliers
Hose Remover Pliers
Clic-R Collar Pliers

9pc Hose Clip Pliers Set
Hose Clamp Pliers
Swivel Jaw Spring Wire Clip Pliers
Swivel Jaw Spring Band Clip Pliers
Flat Band Clip Pliers
Angled Flat Band Clip Pliers
Hose Remover Pliers
Clic-R Collar Pliers
Screwdriver
Hose Pick Tool

220mm Automotive Relay Pliers
To release and refit vehicle electrical relays.
With thin tips and offset handles
for easier access than traditional pliers.
Forged metal handles and PVC dipped grips.
Essential for vehicle technicians and mechanics.

Exhaust Hanger Pliers
for removing the Rubber Grommets from exhaust mounts
Fits a wide range of vehicles and models
Saves time and energy.
Long rubber dipped handles to avoid hot exhausts.

Digital Battery Tester
125A battery load tester for 12V DC lead acid batteries
Battery condition LEDs give a very clear indication of the test results

Heavy-Duty Smart Trolley Battery Charger & Starter
LCD Display for easy reading with Slow and Fast Charge modes.
Input : 220V - 240V AC | 50 - 60Hz | 13A
Output : 12V DC - 10A /30A / 60A
Output : 24V DC - 5A /15A / 30A
Engine-cranking : 12V DC / 200A / 5s on / 180s off
Protected against Overcharge / Short Circuit and Reverse Polarity.
Supplied with Smart Clamp Leads.
Suitable battery types : STD | AGM | GEL | LifeP04

2pc Automotive Battery Terminal Cleaner Set
Fits all terminal posts
Wire Brush for removing corrosion build-up
on battery posts and Terminals for improved electrical contacts.

Electronic Stethoscope Kit
Detect and identify noisy components
Super sensitive microphone with cushioned headphones
4 Pick-up sensors with 4.8 metre long cord

Digital Multimeter
LCD Display with Max. reading : 1999
Overload protection
Low battery indication
Measurement Functions : AC Voltage
DC Current | DC Voltage | Resistance and Diode.
Ideal for use in the Home / Laboratory or Workshop.

Automotive Clamp Meter
Digital LCD Screen Max. reading : 1999
Overload Protection | Auto Ranging | Zeroing Function
Max. Measurable Conductor : 25mm diameter
Voltage AC / DC : 600V
Current AC : 20 / 200 / 600A
Resistance : 2k Ohms
Continuity : Yes
2 x 3V CR2032 Batteries

6pc 3/8in.Dr Socket Set for Glow Plugs
Sizes : 8 | 9 | 10 | 12 | 14 | 16mm with Universal Joints
85mm Long
Chrome Vanadium

Glow Plug Removal & Re-Thread Set
For removing damaged or difficult glow plugs from the cylinder head
also Re-Threading 8mm or 10mm glow plug ports
Ratchet T-Bar | Drill Holding Adaptor
Puller Outer Housing and Adaptor Mandrels | Force Screw / Nut
Top Connection Removal Tool Star socket
Pilot Drills : 3.5mm | Pilot Drill Centring Sleeves
Step Drill : 5.5 - 9 - 10mm
Taps : 1/4in. | M8 | M10
Allen Key

30pc Alternator Service Kit
1/2in.Dr - 10mm Hex Shank Adaptor.
1/2 | 3/8in.Dr Star / Spline and Hex Bits to fit most alternators.
Ideal for BOSCH alternators with free wheel pulleys.

8pc Common Rail Diesel Injector Repair Kit
For repairing common rail diesel injectors Bosch / Siemens and Denso.
Set comes with all necessary sockets to open up defective injectors :
Injector ball valve lapping tools
Hex Bits : 6.6mm | 7.6mm
Denso common rail injector valve seat removal tool
8 Sided socket for Bosch common rail injectors
Inside fixing removal tool for Siemens common rail injectors.

11pc Electronic Fuel Injection Test Light Set
Crucial for electronic fuel injection systems
Systems covered :
TBI - Ford | GM | Geo
PFI - Bosch | GM
SCPI - GM / Multec 2 / 1987
GM 1982 equipped vehicles.

6pc EGT Sensor Socket Set - 3/8in.Dr
For Exhaust Gas Temperature Sensors.
Sizes : 13 | 14 | 17mm Deep and Shallow.
For removing most EGT sensors used on
Cars / light / medium and heavy duty trucks.

Wi-Fi Endoscope - 5V DC
Suitable for pipeline inspection, air conditioning unit inspection,
venting systems and automobile applications.
Support System : IOS / Android
Camera Outer Diameter : 7.9mm
Image / Video Resolution : 2560 x 1440 / 1280 x 720.
Focal Length : 2 - 10cm
Frame Rate : 20fps
Viewing Angle : 70 degrees
Lights : 8 adjustable white LEDs

Engine Compression Test Kit
Compression pressure testing up to 50 bar.
Suitable for most petrol and modern HDI / TDCI
pump injector and older diesel engines.
Quick couplings for straight or angled versions.
Glow plug adaptors | Spark plug adaptors M10 / M12 / M14 and M18.
Injector adaptors M20 / M22 / M24 and stanadyne injectors
Additional pressure gauge for pressure drop test.
Suitable for most cars / trucks / buses / agricultural and marine engines.

Petrol Engine Compression Test Set
Thread Chasers : M10 | M12 | M14 | M18
with Dual Scale Gauge for direct and indirect injection engines.
For use on engines with deep seated plug ports with difficult access.
Built-in pressure relief valve enables repeat tests without dismantling.

Automatic Wave Box Pressure Meter
Diagnose problems with oil pressure in virtually all diesel and petrol engines.
Dual scale gauge : 0 - 500psi / 0 - 35bar
Hose : 1800mm 1/8 NPT oil proof.
Includes 1/4 and 3/8 NPT Adaptors.

2pc Brake Caliper Seal Groove Cleaner Set
200mm Long with different heads
For removing dirt and debris from seal ring grooves.

VAG Fuel Pump Sprocket Puller
For the removal of the high pressure pump sprocket.
on 1.6L and 2.0L TDi common rail diesel engines.
Also for removing the Pump Pulley on
1.6 / 2.0 - 6 cylinder TDi common rail diesel engines
OEM Code : T40064

46pc Harmonic Balance Puller Set
Removes Harmonic Balancers / Gear Pulleys
Steering Wheels and Crank Shaft Pulleys
Zinc Plated Yoke and Bolts
5in. Pressure Screw
Small Cantering Adaptor
Large Cantering Adaptor
Flat Shaft Adaptor

BMW Single VANOS Camshaft Timing Kit
For setting engine timing during chain removal and installation.
Compatible with some BMW 4 and 6 cylinder none VANOS engines
With Camshaft Locking Plate
VANOS Turning Wrench
and Top Dead Centre Pin

BMW Timing Tool Set
For engine codes : N51 | N52 | N53 | N54
With Camshaft and Crankshaft Locking Tools
Transmitter Wheel Locking Tool.
Suitable for a wide range of models.

BMW Timing Tool Set
for N63 / N74 / S63 Models
N63 engines up to September 2012.
N74 V12 Engines which are not very common.
S63 engines prior to September 2011.

BMW / Mini Timing Tool Set
for BMW / Mini One 2001-06
Mini Cooper 2001 - 06 and Mini Cooper S 2002 - 06
Set contains Camshaft Sprocket Holding Tool
Engine Support Bracket and Tension Assembly Tool
This kit is specifically designed for petrol engines on pre 2009 Mini One / Cooper and Cooper S models.
Engine Codes : W10 | W11 | N14

BMW / Mini / PSA Timing Tool Set
For timing 1.4 & 1.6 Valvetronic direct injection chain drive petrol engines
fitted in BMW Mini / Citroen and Peugeot vehicles.
With Camshaft Locking Tools
Camshaft Alignment Clamp and Crankshaft Setting Pin.
M6 Setscrews Chain Tensioner.
Mini Cooper / Coupe | Citroen C4 | Peugeot 207 / 308 / 3008 / 5008

Chrysler Timing Tool Set
for Chrysler Belt Drive Engines
With - Camshaft Locking Pins
Flywheel Locking Pins
Balance Shaft Locking Pins
Tension Adjustment Wrench
Applicable to : Voyager | Grand Voyager
Jeep Cherokee / 01 - 08 | LDV Maxus / 05 - 08

Fiat Timing Tool Set
Crankshaft Locking Tool
Camshaft Setting Tool
Camshaft Sprocket Locking Tool
Camshaft Cover Aligner
Tension Adjuster
Camshaft Aligning Tool
Engine Codes : 169A4 000 | 188A4 000
199A4 000 | 199A7 000 | 350A1 000

Ford Timing Tool Set
for Ford 1.6 TI-VCT Duratec Engines
For timing belt replacement on 1.6 Ti-VCT Duratec EcoBoost Engines.
With Camshaft / Crankshaft and Flywheel Locking Pins
used to lock the camshafts in their timed position
when removing belts and pulleys during servicing.
Suitable for many other petrol and diesel Ford engines.

JLR Timing Tool Set
For Jaguar Land Rover 2.0 Chain Drive Petrol Engines
With crankshaft pulley and crankshaft sensor positioning tools

Ford Timing Tool Set
For locking and checking the camshaft on -
Ford / Jaguar 2.0L EcoBoost / Duratec Petrol Engines.
Land / Range Rover 2.0L GTDI and Si4 Diesel Engines.

Mercedes Timing Tool Set
Timing Chain Mounting Tool Set
for Mercedes-Benz M651 Diesel Engines
Allows precise positioning by preventing the timing chain skipping
and the camshaft sprockets moving when replacing the timing chain
without removing the camshaft sprockets.
Camshaft - Adjusting Tool and Special Wrench
Crankshaft Turning Tool
Sprocket Feet Shaft plus Screws
Timing Chain Guide Tool plus Screws

Mercedes Timing Chain Riveting Tool
For renewing and riveting timing chains on Mercedes-Benz Vehicles
Dismantling the timing chain case is often not required
as the new chain can be fed through using the existing chain.
Suitable for models with Duplex and Simplex timing chains with 4mm chain bolt.

Mercedes Timing Tool Set
Camshaft Alignment Tool Set
For Mercedes-Benz M271 Petrol Engines
Used for engine timing and belt changing.
Also other camshaft related servicing

Vauxhall / Opel Timing Tool Set
for 1.9 CDTI Diesel Engines
Timing and Locking Tool Kit for Camshafts and Crankshafts.
For Servicing and adjusting Timing belts -
includes Flywheel Holding Tool
Applicable to : 1.9 CDTI / TID / TTID & 2.0 CDTI / ECOFLEX

Camshaft Sprocket Locking Timing Tool Set
for Renault 1.8 / 2.0 F4 16V Vehicles -
Laguna II / 2001 - 2009
Megane II / 2002 - 2009
Scenic / 2002 - 2009
Engine Codes : F4P | F4R
OEM Codes : MOT1509-01 | 1509.

Renault Timing Tool Set
for 1.4 / 1.6 / 1.8 / 2.0 16V Belt Drive Engines
Suitable for timing belt replacement on
Renault and some Nissan and Vauxhall / Opel vehicles.
With Camshaft Rule and Locking Pins.
OEM Codes : MOT1489 | MOT1496 | MOT1054

VAG Timing Tool Set
for Porsche Cayenne and Panamera V8 Engines
Also Porsche Cayenne utilizing the M97/01 V8 engine.
For camshaft timing on Direct Fuel Injection /
Turbo and Normally-aspirated Engines
Allows TDC Timing during servicing the
Camshafts / Cylinder Head / Timing Chain
or Variable Valve-timing Cam Phasers.
Cayenne V8 up to 2007 and Cayenne and Panamera 2008 onwards

Volvo Timing Tool Set
for B4204 8 Speed Transmission Engines.
For aligning the camshaft and crankshaft and
working on valve drive and renewing the cylinder head gasket.
Belt Pulley Counter Holding Tool
Crankshaft Wheel Puller
Radial Seal Ring Mounting Tool
Camshaft Sprocket Tool
Camshaft Alignment Tool

Antifreeze and Coolant Tester
Easy read scale and pointers.
Calibrated in degrees C and F.
Tests ethylene glycol strength and includes temperature adjustment scale for accurate interpretation of mixture strength.
Tests Ethylene Glycol strength while the engine is hot or cold.
Composite body and rubber bulb for workshop durability.

8pc Block Tester Kit
Detects exhaust gasses in the radiator
and checks for gasket damage also cracked or warped cylinders.
Works with Petrol | Diesel and Gas powered vehicles.
Use with combustion leak detector fluid - not included.
Suitable for use with sets - CT1585 and CT3380.

12V Smoke Leak Detector
For detecting leaks in pipe systems on cars and motorcycles
such as fuel pipes / air intakes and the radiator.
Smoke output value : 1 - 6 L/min
Output Pressure : 10 - 18psi
With Built-in air pump / Controllable flow value
Test Oil Capacity : 100ml
Supplied with all accessories needed.

Tube and Trim Cutter
With Multi-Angle Anvil and replaceable Utility Knife Blade.
Anvil Markings for 45 to 120 degree Angles.
Ideal for cutting Window Gaskets
Plastic Trim | Tubing and Conduit.