6pc Star / E-Type Sockets
Sizes : E10 | E12 | E14 | E16 | E18 | E20.
1/2in.Dr x 140mm long
Used for cylinder head bolts

Oxygen Sensor Socket
Size : 22mm x 6pt
Length - 150mm
For removing and installing deep-seated Lambda Oxygen Sensors.
Particularly suitable for Audi / BMW / Ford / Mercedes / Opel
Rover / Seat / Skoda / Vauxhall / Volvo.

7pc 3/8 & 1/2in.Dr Oxygen Sensor Socket Set
For removal or replacement of Heated and Non-Heated Oxygen Sensors
Cut-Away sections allow sockets to fit over wiring harnesses
Sizes : 7/8in. | 22mm | 27mm | 29mm
22mm Wrenches Deep and Shallow

14pc Diesel Injector / Lambda Socket Set
1/2in.Dr
Hex : 20 | 22 | 27mm
Bi-Hex : 17 | 19 | 21 | 22 | 27 | 28 | 30mm
For installing and removing oxygen sensors and diesel injectors.

Exhaust Hanger Pliers
for removing the Rubber Grommets from exhaust mounts
Fits a wide range of vehicles and models
Saves time and energy.
Long rubber dipped handles to avoid hot exhausts.

Exhaust Support Pliers
For removing the Rubber Grommets from exhaust mounts.
Fits a wide range of Vehicles, Vans and Larger model Cars.
Long rubber dipped handles to avoid hot exhausts.
With self-centring movable pin.
Length : 360mm

Exhaust Clamp Pliers
300mm Long with 60mm Jaw Capacity
Suitable for Citroen / Peugeot / Renault vehicles

Lambda Sensor Remover / Installer
22mm / 200mm long for excellent access.
For use with an air hammer to aid loosening stuck lambda sensors.
3/8in. Dr head which allows the use of a torque wrench when tightening sensors.
Use air hammer for extraction ONLY - for fitting use 3/8in.Dr hand tool.

Lambda Sensor Remover / Installer
22mm / 200mm long for excellent access.
For use with an air hammer to aid loosening stuck lambda sensors.
3/8in. Dr head which allows the use of a torque wrench when tightening sensors.
Use air hammer for extraction ONLY - for fitting use 3/8in.Dr hand tool.

Swivel Head Oxygen Sensor Wrench
7/8in. / 22mm

22mm Lambda Socket
1/2in.Dr
85mm Deep

Lambda Tester and Simulator
Tests Zirconia and Titania lambda sensors and ECU.
Suitable for 1 / 2 / 3 and 4 wire sensors - heated and unheated
LED display shows crossover signal from sensor.
Simulates rich or lean mixture signals to check ECU response
Insulation piercing clip for quick and easy connection.
Displays and confirms wire identity.
Low battery indicator / 9V battery supplied.

Accelerator / Brake Pedal Adjuster
Sets engine speed to check emissions.
Ideal for MOT check
Length : 710mm

3pc Diesel Oxygen Sensor Socket Set
28mm Injector Socket 1/2in.Dr 12 point
7/8in. Injector Socket 1/2in.Dr 12 point
7/8in. Long-reach Vacuum Switch Socket
applicable to a wide range of vehicles

5pc Oxygen Sensor Set
Slotted sockets with Thread Chasers
22mm x 80mm Deep - 3/8in.Dr
22mm x 31 mm Offset - 3/8in.Dr
22mm x 50mm Offset - 1/2in.Dr
M12 and M18 Thread Chasers

2pc Oxygen Sensor Socket Set
Sizes : 7/8in. with 3/8in.Dr
22mm with 1/2in.Dr

7pc Sensor / Thermo Switch Socket Set
for Special Applications
3/8in.Dr sizes : 10 | 11 | 12 | 13| 14mm
1/2in.Dr sizes : 17 | 19mm.
For top and side wired Temperature Sensors
Thermo Switches and other components.
Also suitable for nuts and bolts of bent pipes.
Slot widths : 7.4 | 8.8 | 9.1 | 10.5 | 13.3 | 14.4 mm

2pc Oxygen Sensor Thread Chaser
Sizes : M12 x 1.25 and M18 x 1.5
Used for cleaning and rethreading damaged oxygen sensor ports.

Oxygen Sensor Thread Repair Kit
18.6mm Reamer for oxygen sensor threads.
M20 x 1.5 Tap for cutting the repair bushing threads.
M18 x 1.5 Tap for cutting of oxygen sensor threads.
Insertion Tool with 5 Repair Bushings.
Designed for

Fuel Vaporiser Spanner & Thread Chaser
22mm / 6 point for removing Ford DPF Fuel Vaporiser
on 1.6 / 2.0 / 2.2L Duratorq Ecoblue Diesel Engines 2012 onwards.
Useful tool due to very restricted access to the vaporiser.
M20 x 1.5mm Thread chaser to clean and reform damaged threads.
Use with 21mm spanner or socket.
Chrome Molybdenum

Fuel Vaporiser Port Thread Chaser
for Ford M20 x 1.5mm Exhaust System
Suitable for cleaning and reforming threads on most
Ford exhaust system fuel vaporiser ports.
The short lead-in on the thread chaser allows for thread to be cut
as close as possible to internal seat of the exhaust.
With rubber O-ring to hold the chaser in a place
using suitable 21mm socket or spanner.

Nitrogen Oxide Sensor Port Thread Chaser
For use on any M22 x 1.5 thread
For sensor ports often used for Nitrogen Oxide sensors
suitable for cleaning or repairing damaged port threads
prior to new sensor being fitted.
Applications : Mercedes-Benz | Vauxhall | Opel
With rubber O-ring to hold the chaser in a place
using suitable 21mm socket or spanner.

Exhaust and Tailpipe Cutter
Cutting Capacity : 75mm diameter
Suitable for cutting thin-wall tubing up to 2.5mm thick.
Designed to enable access where space is restricted.
Ideal for cutting plastic / copper / aluminium and steel pipe.
Vice grip mechanism provides pressure in use reducing hand fatigue.

Exhaust Pipe Cutting Pliers
for Single wall pipes from 19 to 83mm
15 Steel Cutting Discs allow 90 degree complete cut.
NOT for use on Stainless Steel exhaust pipes.

Extra Wide Tube Cutter
Ratchet Type ideal for Exhaust Pipes
Jaw Size : 28 - 67mm

Replacement Cutting Wheel
for Pipe or Tube Cutter CT0756

315mm Exhaust Pipe Remover
For removing the rubber straps on exhaust systems
Hook shaft diameter : 6mm

2pc Exhaust Rubber Ring Tool Set
Hooked and 90 degree Flat
T-handles for extra leverage and rotation
Suitable for most vehicle rubber ring exhaust mountings

Exhaust Spring Clamp Removal Tool
Length : 150mm / 6in.
Use with a 17mm Spanner
For early VW vehicles : Golf | Jetta | Passat

3pc Pipe Expander Set
Works With all 1.1/8 - 3.5in. Thin Walls
Small Expander - 1 1/8 to 1 3/4in. / 28mm - 45mm
Medium Expander - 1 1/2 to 2 1/2in. / 38mm - 64mm
Large Expander - 2 1/8 to 3 1/2in. / 54mm - 90mm
Easily Straighten out Clamp dents in exhaust pipes

Exhaust Pipe Expander Kit
This kit provides the handy collets and expander required to stretch tailpipes
before making tight seals to pipes with smaller diameters.
Collets for a broad expansion range from 1-5/8in. to 4-1/4in.
Can be used with an impact wrench to quickly stretch pipes.

Exhaust Back Pressure Test Kit
This kit connects to the oxygen sensor port to monitor exhaust back pressure
allowing the testing of exhaust systems and catalytic converters.
May be used during test drive conditions.
Pressure gauge 0 - 20psi.
Connection hose 300cm with heat protection jacket.

6pc EGT Sensor Socket Set - 3/8in.Dr
For Exhaust Gas Temperature Sensors.
Sizes : 13 | 14 | 17mm Deep and Shallow.
For removing most EGT sensors used on
Cars / light / medium and heavy duty trucks.

Tap with Guide Bolt for Temperature Sensors
Size : M12 x 1.25
with Hexagon drive for perfect power transmission.
For re-cutting rusted and damaged probe threads.
Ideal for NOX and particle filter sensors on exhaust systems.
With 6 cutting edges for ideal centring.
Especially short execution.
With cleaning grooves in the guide bolt.
Ideal for confined spaces.

Tap with Guide Bolt for Temperature Sensors
Size : M14 x 1.5
with Hexagon drive for perfect power transmission.
For re-cutting rusted and damaged probe threads.
Ideal for NOX and particle filter sensors on exhaust systems.
With 6 cutting edges for ideal centring.
Especially short execution.
With cleaning grooves in the guide bolt.
Ideal for confined spaces.

Tap with Guide Bolt for Temperature Sensors
Size : M16 x 1.5
with Hexagon drive for perfect power transmission.
For re-cutting rusted and damaged probe threads.
Ideal for NOX and particle filter sensors on exhaust systems.
With 6 cutting edges for ideal centring.
Especially short execution.
With cleaning grooves in the guide bolt.
Ideal for confined spaces.

Tap with Guide Bolt for Temperature Sensors
Size : M18 X 1.5
with Hexagon drive for perfect power transmission.
For re-cutting rusted and damaged probe threads.
Ideal for NOX and particle filter sensors on exhaust systems.
With 6 cutting edges for ideal centring.
Especially short execution.
With cleaning grooves in the guide bolt.
Ideal for confined spaces.

Tap with Guide Bolt for Temperature Sensors
Size : M20 X 1.5
with Hexagon drive for perfect power transmission.
For re-cutting rusted and damaged probe threads.
Ideal for NOX and particle filter sensors on exhaust systems.
With 6 cutting edges for ideal centring.
Especially short execution.
With cleaning grooves in the guide bolt.
Ideal for confined spaces.

Tap with Guide Bolt for Temperature Sensors
Size : M22 X 1.5
with Hexagon drive for perfect power transmission.
For re-cutting rusted and damaged probe threads.
Ideal for NOX and particle filter sensors on exhaust systems.
With 6 cutting edges for ideal centring.
Especially short execution.
With cleaning grooves in the guide bolt.
Ideal for confined spaces.

2pc Tap Set with Guide Bolt for Sensor
Sizes : M20 x 1.5 | M22 x 1.5
with Hexagon drive for perfect power transmission.
For re-cutting rusted and damaged probe threads.
Ideal for NOX and particle filter sensors on exhaust systems.
With 6 cutting edges for ideal centring.
Especially short execution.
With cleaning grooves in the guide bolt.
Ideal for confined spaces.