4pc Injector Socket Set 1/2in.Dr
Sizes: 25 | 27 | 29 | 30mm
For removing the top cap and connectors on diesel fuel injectors.
Deep sockets with wide cut-out for the most popular injectors in modern vehicles
Chrome Vanadium

4pc Diesel Truck Injector Socket Set
70mm 4 Teeth with M14 x 1.5mm receiver thread
72mm 4 Teeth
120mm 4 Teeth
120mm 3 Teeth for injectors with electrodes

4pc Diesel Truck Injector Socket Set
for working on nozzle holders
1/2in. Dr Socket - 72mm long with 4 teeth
2 Sockets with 32mm outer hexagon and 4 teeth
1/2in.Dr Socket - 120mm long with 3 teeth

1/2in. and 3/4in. Drive
Sizes - 25 / 27 / 28 / 29 / 30mm
Suitable for most Injectors with Bosch and Siemens nozzles
Suitable for Citroen / Peugeot vehicles

9pc Diesel Injector and Glow Plug Socket Set
1/2in.Dr Diesel Injector Sockets :
21mm x 90mm |
22mm x 78mm | 22mm x 110mm
27mm x 78mm |
28mm x 78mm | 28mm x 83mm
3/8in.Dr Glow Plug Sockets :
8 | 10 | 12mm x 158mm long with Universal Joint.

6pc Diesel Injector Removal Set
Adaptor sizes :
M20 x 1.5 inner thread to M14 x 1.0 inner thread
M20 x 1.5 inner thread to M17 x 1.0 outer thread
M20 x 1.5 inner thread to M20 x 1.0 outer thread
M20 x 1.5 inner thread to M25 x 1.0 outer thread
M20 x 1.5 inner thread to M27 x 1.0 outer thread
10mm Tamper-proof Hex Bit / 1/2in.Dr Socket
For removing Bosch / Denso / Siemens and Delphi injectors.

Fuel Injector Remover
for Jaguar and Land Rover 5.0L V8 Engines - 2003-2016.
Designed to fit long petrol injectors in Supercharged engines.
Slide hammer shaft helps to improve access when working
on the rear most injectors.
OEM Code : 310-197

Fuel Injector Extractor Set for Ford / Volvo
Special designed tool kit for removing fuel injector nozzles on -
Volvo S60 | V40 1.6 T4 Engines
Ford Vehicles with EcoBoost Engines.
OEM Codes : 1 310-206 - Ford | 2 9997410 - Volvo

3pc Fuel Injector Extractor Set
Suitable for Mercedes CDI engines
Impact Extractor - 1.85kg / 470mm
Injector Claw
Injector Adaptor

6pc Diesel Injector Extractor Set
Fuel injector puller for new generation trucks.
Applicable to trucks with injector-pump systems
or with traditional truck injectors on -
Volvo / Scania / Mercedes / MAN / Renault / IVECO.
With Socket for Delphi injectors / Injector Hook / Extension and Upper handle
Body-tamper / Universal joint / M18 x 1.5 nut.

9pc Injector Extractor Set
For removing seized injectors without dismounting the cylinder head.
Slide Hammer : 350mm / 1.75kg
Adaptor / Puller : M12 x 1.75P
Adaptor : M17 x 1.0
Adaptor : M27 x 1.0 for bosch injector nozzle
Suitable for Mercedes and other vehicles.

14pc Injection Puller Set
For the reliable removal of Bosch / Delphi / Deso and Siemens diesel Injectors
1/2in.Dr Injector Sockets - 25 / 27 / 29 / 30mm
7 Injector Adaptors and Slide Hammer

Fuel Injector Removal Tool Kit
for use with a Air Hammer.
Specifically designed to aid the removal of seized Injectors.
To be used in collaboration with Air Vibration Hammers.
Allows impact force and vibration to any adaptor with a 5/8

17pc VAG Fuel Injector Service Kit
for the removal and installation of petrol injectors on VAG vehicles.
Applicable to : 1.4 | 1.6 | 1.8 | 2.0 | 2.7V6 | 3.2V6 | 3.6V6 and 4.2V8 FSI engines.

15pc VAG Fuel Injector Service Kit
Suitable for VW / Audi / Seat / Skoda FSI injectors
with Direct Injection or Pump-Injector engines.
Slide hammer / Puller / Puller Claw for dismantling FSI injectors
Cone an Calibration tools for mounting the combustion chamber rings.
Built-in pin for mounting the FSI injectors
Extractor for dismantling pump-injector units

Diesel Injector Master Kit
Suitable for the removal of Bosch / Delphi /
Denso / Siemens and Pumpe Duse diesel injectors.
1.3kg Slide Hammer with 150mm Shaft.
4kg Slide Hammer with 400mm Shaft and Handle.
With various Male and Female Adaptors.
Pump Duse Injectors Adaptors.
Injector Sockets - 25 | 27 | 29 | 30mm

Pneumatic Injector Removal Tool Set
Air Pressure : 0.5 - 0.8bar provides impact
to disassemble particular tight fuel injectors
with a universal 21 piece adaptor set that cover
Bosch / Delphi / Denso / Siemens CR injectors
which have solenoid coil or screw connections.
M14 | M16 | M18 | M20 | M22 | M8-C | M8-X | M10

Pneumatic Injector Extractor / Puller Tool Set
This tool is designed to combine pneumatic force with controlled vibration,
enabling the safe and efficient removal of seized fuel injectors
without damaging the cylinder head or breaking the injectors.
Equipped with a selector switch to choose between Slow
and Fast vibration settings for precision and control.
Designed to disassemble stubborn or tightly fitted injectors.
Mercedes-Benz / Citroen / Fiat / Peugeot
Suitable for use on Bosch / Delphi / Denso / Siemens
injectors with solenoid coil or screw connection.

Master Injector Extractor Kit with 10 Ton Hydraulic Cylinder
Suitable Diesel Fuel Injectors :
Bosch : M17 x 1.0
Delphi : M14 x 1.5 Delphi
Toyota : M16 x 1.0 Toyota
Denso : M20 x 1.0
Siemens : M25 x 1.0 / M27 x 1.0
Can be used in-situ saving time and expense.
Main side and top bars allow for various engine configurations.

Diesel Injector Extractor Set
With adaptors and Slide Hammers -
1.6kg | 2.7kg | 5.1kg
Pulling Claws with fork opening.
5 slotted 6 point 1/2in.Dr sockets -
25 | 27 | 28 | 29 | 30mm x 100mm
Injector extractor sleeve with shells.
M27 Pulling adaptors.

Fuel Injector Removal / Installation Tool Kit
for BMW MINI Petrol Engines B38 / B48
For extracting or fitting plastic bodied petrol injectors
used on some BMW and MINI engines also reducing
the chance of damage to the injectors while removing them.
OEM Codes : 2358417 | 2358022.

BMW Fuel Injector Service Kit
Bosch and Common Rail injectors
mounted on many BMW vehicles.
No need to dismantling the cylinder head.
Blower adaptor to clean the injector seats.
M16 - M17 forcing screw | support feet
Hex wrench to remove solenoids
29mm injector socket with 1/2in.Dr

29mm Fuel Injector Socket
1/2in.Dr
for BMW Common Rail Injectors
Replacement socket for CT3617

Diesel Injector Removal Hydraulic Upgrade Kit
Providing 17 Ton Hydraulic force for diesel injector removers allowing
the controlled extraction of very tight fitting or struck injector nozzles.
Can be used in conjunction with CT3617
Hydraulic Cylinder with M16 x 1.5 Nut and Spacer Ring.
Pull Spindles M14 x 1.5 external thread - 240 / 315mm
Pull Spindles M17 x 1.0 internal thread - 240 / 315mm
Pull Spindle M18 x 1.5 internal thread - 250mm
Pull Spindle M25 x 1.0 internal thread - 240mm

Petrol Injector Extractor Set
For BMW N54 / N63 and Mini N14 / N18
Designed to remove injectors and re-install the Teflon seals.
Includes : Slide-Hammer and Adaptor
70mm Short Bolt | 120mm Long Bolt
Tapered Cone and Small / Medium and Large Diameter Sleeves.

Fuel Injector Service Tool
For the removal and installation of high pressure injectors
with hold down top found in the BMW N20 and N55 series engine.
Coated steel and anodised aluminium
OEM Code : 130320

Petrol Injector Remover with Slide Hammer
for BMW N43 | N53 | N54 models
Access directly below injector and held by thumbscrew
Suitable for BMW : 1 | 3 | 5 | 6 | 7 series
OEM Code : 130180

BMW Fuel Injector Service Tool Kit
Designed to install and remove high pressure injectors
also injectors with hold down tops found in BMW N series engines.
Applicable to : BMW N20 | N47| N54 | N55 | N57 | N63 models.
OEM reference : 130180 / 130270 / 130320

Diesel Injector Puller with Adaptor
Aids Removal of Bosch and Lucas Diesel Injectors
M8 | M12 | M14 Adaptors

Petrol Injector Puller for Ford Vehicles
For removing Bosch GDI Injectors
on all standard Ford EcoBoost petrol engines 1.0 - 3.7 litre capacity.
Extracts petrol injectors easily without damaging the injector or head.
Includes slide ham

Injector Extractor Kit
For extracting seized injectors from Ford 2.0L Diesel Eco Blue engines
as described by Ford. Injector removal is required for any service or repair
work that requires the removal of the cam cover, cylinder head or cam shafts.
CAUTION :
This is for seized injectors only and will render the injector unserviceable.
Applicable to : Ford Edge, Focus, Galaxy, Ranger, S-Max, Tourneo
and Transit fitted with the Eco blue 2.0L diesel engines from approx 2016.
OEM Codes : 303-1690 | 303-1690/1 | 303-1690/2.
Material : S45C / Black Finish

Injector Puller Remover Kit
for Ford 2.0L EcoBlue Diesel Engines.
Removes seized / stubborn injector nozzles
without dismantling the cylinder head.
With pulling spindle / support sleeve / shoulder nut
and 1/2in.Dr injector removal socket
Applicable to :
Ford - Edge | Focus | Galaxy | Ranger | S-Max | Tourneo
and Transit fitted with the EcoBlue 2.0L diesel engines from 2016.
OEM Codes : 303-1690 | 303-1690/1 | 303-1690/2.

Fuel Injector Puller Set
for Alfa Romeo / Fiat / Ford / Iveco / Opel / PSA / Suzuki
1.3 / 1.6 / 1.9 / 2.0 - 16 Valve Engines - Also 2.3 and 3.0 models
Specifically designed for the removal of extremely seized injectors.
With the application-specific extractor -
the injectors can be removed either hydraulically or mechanically.

Kia / Hyundai Injector Remover Kit
For removing injectors from most Korean vehicles -

Kia : Carnival | Rio | Careens | Cerato | Optima
Picanto | Sorrento | Sportage | Grand Carnival.

Hyundai : Starex | Lavita | Matrix | Trajet | Terracan
Santa FE / SM | Libero | Avante XD | Tucson |
Grandeur XD Getz | NF Sonata | Accent / 06

Diesel Fuel Injector Puller
with Injector Cap removal socket and Security Hex Key
Specially designed for the removal of stubborn diesel injectors on Mercedes CDI engines.
Designed to remove the injector without damaging the cam cover.
For C-Class / E-Class and Sprinter Vehicles

4pc Injector Puller Set
for Mercedes CDI Engines
10mm Hex Bit with integral 1/2in.Dr socket
29mm Slotted Injector Socket with 1/2in.Dr or use with 22mm spanner
Pulling spindle : 34mm dia with 20mm Slot
Protection Rings
Ideal for removal and installing tightly fit common rail injectors
as found on Mercedes CDI 611 / 612 and 613 engines.

6pc Injector Puller Set
for Mercedes CDI engines
For removing common rail injectors
without having to disassemble cylinder head.
Applicable to Mercedes-Benz
CDI engines 611 | 612 | 613 etc.
Injection puller with impact hammer.

Diesel Injector Puller
For Citroen / Peugeot 2.0 / 2.2HD1 injectors.
With Pulling Bridge and 3 Bridge Legs
Injector Sockets : 25mm | 29mm Diameter
Injector Force Screw Threads :
17mm Male x 1mm Pitch
25mm x 1mm Pitch
Security Hex Key : 10mm

Injector Removal Extraction Tool Kit
Designed to remove the injectors on Renault Trafic 2.0 DCI M9R Engines.
Also used in Nissan vehicles and Vauxhall Vivaro.
Includes 2 Force Screws :
M14 x 1.5mm Female Force Screw for Piezo Injector
M17 x 1.0mm Male for Solenoid type Injectors.

Diesel Injector Puller
For removing Diesel injectors on VAG vehicles
fitted with 1.6 and 2.0 CR TDi Engines.
With Slide Hammer / Injector Adaptors and fixings.
No need to remove solenoid.
OEM Codes : T10402 | T10415

Injector Nozzle Puller - Volvo HGV
Designed to aid extraction of the unit-injectors from Volvo HGV engines.
Ideal where the unit pump has overheated and stuck in the cylinder head.
Applicable to :
Volvo trucks - FM12 | FM440 | FH500
Volvo Penta marine engines - D9 | D12 | D16.
Includes slide hammer and
Puller Attachment Clamp to keep the assembly in place.

Injector Sleeve Service Set - Volvo FM Trucks
For removing or installing HGV Injector Sleeves.
Applicable to Volvo FM12 Trucks.
Contains Pre-Cutter and Removing and Mounting Tools
OEM Codes : 9998252 | 9998253 | 9998688.

7pc Injection Puller Set - VAG TDI
For quick and precise extraction of Injection Nozzles from Diesel Engines
Suitable for Audi - VW diesel vehicles - SDI / TDI / PD

Injector Sleeve Service Set - Volvo FM Trucks
For installing and removing sleeves from the cylinder head.
Sleeves need to be replaced when the truck seems powerless
and smokes with black clouds.
Two Leg Puller | Extractor Unit
Injector Sleeve / Pre-Cutter / Removal and Mounting Tools
OEM Codes : 21515329 | 88800387
9986174 | 9998252 | 9998253 | 9998688

Injector Sleeve Service Set - Volvo FM12 Trucks
For installing and removing sleeves from the cylinder head.
Sleeves need to be replaced when the truck seems powerless
and smokes with black clouds.
Two Leg Puller
Extractor Unit
Injector Sleeve Mounting Tool
OEM Codes : 88800387 | 9986174 | 9998688
Use in conjunction with sleeve installer kit - CT6715

Fuel Injector Sleeve Installation Kit
Applicable to Volvo FM12 Trucks.
For use with injector sleeve remover and installer set -
See CT6713 / CT6714
OEM Code : 21515329.

Diesel Injector Puller Set
With Special 1/2in.Dr Hex Bits
Suitable for the fast and reliable removal of
Bosch | Delphi | Deso and Siemens Diesel Injectors.

Fuel Pump Removal Tool
for BMW X1 | X3 N47 2.0 Diesel Engines
Applicable to :
1 Series : E81 | 82 | 87 | 88
3 Series : E90 | 91 | 92 | 93
5 Series : E60 | 61
X1 and X3 : E83
and all chain driven engines.
OEM Code : 118740

BMW Injection Pump Wheel Assembly Tool
For Holding the sprocket during assembly of the injection pump.
Suitable for BMW engines : M47 | M47T2 | M47TU | M57 | M57TU

Mercedes Diesel Fuel Injection Pump Socket
33 point Spline | 1/2in.Dr | 56mm Long
For injection pumps on Mercedes-Benz
601 | 602 | 603 | 605 | 606 | 615 | 616 | 617
Also fits many early 250 and 300 models
with in-line fuel pumps.