Universal Bearing Packer
111mm Cone Diameter.
Suitable for packing bearings with an even spread of Grease.
A Clean and Quick method - place bearing on to the bottom cone
screw down the cone lid and pump grease into nipple.
Works on most tapered roller bearings found on cars / boats and trailers.
Knurled grips for oily fingers.

Universal Wheel Bearing Spreader
Designed to separate the suspension strut from the wheel bearing housing.
Spreading range : 5.0 - 11.5mm
Drive : 17mm Hex

Master Bearing Race and Seal Driver
Aluminium all in one self contained precision driver with rotating handle and expanding jaws to seat races / bearings or seals with ease.
Variable Jaws cover a range of 18.5 - 89mm or 0.72 - 3.50in.

Bearing Race and Seal Driver Set - 7pc

11pc Bearing and Seal Driver Set
For the Installation of Bearings and Seals
Drive Flanges : 39.5 | 44.5 | 50 | 59 | 63 | 65 | 72 | 76 | 81mm
with Aluminium Mandrel Driver

21pc Wheel Bearing and Seal Installation Kit
Suitable for mounting bearings and sealing rings.
Particularly useful when used with a hydraulic press.
Kit includes 17 mounting pads 70 to 150mm diameter in 5mm steps.
273mm handle for use with a hammer.

Wheel Bearing and Seal Installation Kit
New lightweight design to prevent damaging the bearing or housing.
Contains 3 metal bearing drift sleeves
and 34 nylon drifts with Deadblow Hammer.
Can also be used to install oil seals.
Fits most modern vehicles

51pc Bearing / Bushing and Seal Master Driver Set
Suitable for mounting bearings | bushings and sealing rings.
220mm knurled handle grip for use with a hammer.
Particularly useful when used with a hydraulic press.
Support Disc - 74 mm | bore 12.2mm | height 15.2 mm.
48 Discs 18 to 65mm Diameter in 1mm increments
Discs 12.2 mm high and 12.2 mm bore

Wheel Bearing Lock Nut Wrench
Adjustable jaws with locking feature
to suit both hexagon and octagon wheel bearing lock nuts.
6 point lock nuts 49 - 135mm
8 point lock nuts 49 - 143mm
Pin diameters 6mm / 8mm / 10mm

Wheel Bearing Circlip Removal / Assembly Lever Tool
Unique lever tool with specially shaped hook that allows
the easy removal and fitting of wheel bearing internal circlips.
Applicable to Vauxhall / Opel / Ford / PSA / Fiat and VAG vehicles

Bearing Inner Ring Puller - 68mm
For removing the inner wheel bearing rings on wheel hubs.
The bearing rings usually remain on the wheel hub
when the wheel bearings are removed.
Integral Clamp holds the puller legs
securely behind the component to be removed.
Pressure piece diameter : 25 x 30mm
Puller width : 68mm
Puller depth : 60 mm

16pc Bearing Extractor Set
Puller and Slide-Hammer
Screw Adaptors : M6 x 1.0 / M8 x 1.25 / M10 x 1.5
Collets : 8 - 11mm / 12 - 17mm / 18 - 23mm / 24 - 29mm
30 - 34mm / 34 - 38mm / 39 - 43mm / 44 - 48mm / 49 - 53mm / 54 - 58mm
Ideal for dismantling bearings installed in a blind hole.

3pc Bearing Puller Set
Sizes : 3 | 4 | 6in. with Reversible 3 Leg Jaw

5pc Bearing Puller Set
Bearing extractor collets with internal capacity from 11 to 32mm Collets : 10 - 14mm | 15 - 19mm | 18 - 25mm | 25 - 32mm
3/8 - 1/2in. | 9/16 - 11/16in. | 5/8 - 1in. | 1 - 1-1/4in.
Slide Hammer - 377mm / 0.85kg

5pc Wheel Bearing Puller Set
Internal and External 3-Jaw Pullers
External puller 15mm - 80mm
Small Internal puller 15mm - 30mm
Large Internal puller 30mm - 80mm
Slide Hammer to aid pulling out the bearing.

9pc Bearing Puller Set
Removes gears / pulleys and steering wheels.
3lb Slide Hammer with T-handle - 390mm
8 - 10 | 10 - 12 | 12 - 14 | 15 - 17 and
17 - 20 | 20 - 24 | 25 - 29 | 30 - 32mm

Bearing Separator Set
2 Sizes : 50 and 75mm
4 Sets of Hex Push-Puller Legs and Bar-Type Puller Head
125mm Puller Cross-Bar with 160mm Forcing Screw

31pc Wheel Hub and Bearing Service Tool Set
Allows Servicing to the wheel hub and wheel bearings.
Pressure Plates -
50 | 55 | 59 | 63.3 | 66.6 | 70.3 | 71.5 | 73.1 | 73.4 | 74.8 | 77.5 | 81.5 | 83.4mm
Sleeves with following diameters : 76 | 86 | 91 | 102mm
Extractor bolts M12 x 1.5 | M14 x 1.5
Spindle 7/8 x 300mm including thrust bearing
Pressure nut 32 x 60mm and Pressure sleeve 38 x 40mm

14pc Bearing Splitter and Gear Puller Set
With various threaded connector bolts | Bearing Separators | Pawls and Push Rod

Bearing Separator
Drop forged
Clamping Width : 46mm - 230mm max
Clamping Bolt Length : 350mm / Distance : 224mm / Thread : M25 x 2.5
Puller Bolt : 3/4in. x 10 UNC
Puller Bolt distance : 164mm / 350mm max
Splitting Knife Base : 102mm - 288mm max
Suitable for removing bearings / gears and bushings from shafts.

Bearing Separator Puller Kit
For use with CT6292 - Ball Bearing Separator
Includes : 400mm Puller Cross Bar.
455mm Lead Screw with 1-1/8in.thread / 22mm Hex Head.
290mm Push-Puller Legs with 3/4in.thread.
270mm Extension Legs with 3/4in.thread.
For removing gears, pullers, bearings, steering wheels, etc.
Suitable for large bearing removal on vehicles, ATV's and light trucks.

19pc Wheel Hub and Bearing Service Kit
For fitting modern GEN2 Wheel Hub Bearing Units
where the Hub and Bearing are a combined unit.
M18 Pulling Spindle with nuts and thrust bearings.
Heavy Duty Steel Drifts
May be used in conjunction with a Hydraulic Shop Press.

19pc Front Wheel Drive Bearing Service Kit
For the removal and installation of front hub bearings
without the need to dismantle the steering assembly.
Heavy Duty Steel Drifts : 55.5. to. 91mm

25pc Wheel Bearing Installation Set
Front wheel drive vehicles 60mm to 85mm.
Reduces chances of damage to hub and bearing.
Heavy duty steel drifts.
For use with impact tools.
Also suitable for industrial bearings.

Bearing Service Tool Kit for Front Wheel Drive Vehicles

18pc Silent Bearing Tool Set for VAG Rear Axles
For assembly and disassembly of bearings both on and off the vehicle.
For the replacement of silent bearings from the wheel bearing housing
axle guide / trailing arm / wishbone lower / internal as built in
push rod and the upper wishbone not built-in.
For use alongside mechanical spindle.
Applicable to most Audi / VW / Seat vehicles

VAG Wheel Bearing Tool Set
For mainly Audi / VW vehicles
Clamping nut | Pull spindle |
Bearing cover | Housing | Adaptor ring.
Centring Rings 34 to 80mm
Pressure Rings 65 to 85mm
Retainer adaptors for Clamping nut
Pressure spindle and Mechanical spindle

Mercedes Wheel Bearing Tool Set
A | B | C | E | M | V Class | 190 series | W124
Pulling spindle | Bearing cover | Adaptor ring
Centring Rings - 42 to 80mm Diameter
Pressure Rings - 66 to 93mm Diameter
Pressure spindle with O-ring and mechanical spindle
A Professional way to remove and replace wheel bearings.

Peugeot-Citroen-Renault Wheel Bearing Tool Set
Pulling spindle | Bearing cover | Adaptor ring.
Centring Rings - 35 | 37 | 42 | 45 | 60 | 75mm
Pressure Rings - 65 | 72 | 82 | 83mm
Pressure spindle with O-ring and mechanical spindle
A Professional way to remove and replace wheel bearings.

Wheel Hub Bearing Unit Tool Kit
for Citroen / Opel / Peugeot / Toyota Vehicles
For pressing out and fitting compact wheel bearings on
the rear axle without removing the axle knuckle and ABS sensor.
For changing the complete Wheel Bearing / Hub Unit
on the rear axle without removing the axle leg.
The whole procedure takes place directly on the vehicle.
Suitable for compact wheel bearing numbers :
9819074780 | SU001A6528
FAG : 713 6506 80 | SKF : VKBA 7120

VAG Wheel Hub Bearing Tool Set - 62mm
For combined wheel hub and bearing units.
Suitable for direct use on vehicle while in-situ.
Mounting shells and Dismantling shells
Mounting and Dismantling plates
Pressure plate with 8 holes

VAG Wheel Hub Bearing Unit Tool - 66mm
For removing and installing the compact wheel bearing
combined wheel hub and bearing unit on VAG vehicles.
High strength ball bearing fitted spindle.
Applicable to VAG vehicles

VAG Compact Wheel Bearing Set
For removing and installing the compact wheel bearing
combined wheel hub and bearing unit on VW vehicles
with high strength spindle and components

Front Wheel Hub Bearing Unit Tool - 78mm
on Ford | Mazda | Volvo
With Pressure plate and bolts
Disassembly shells and pressure piece
Mounting shells and pressure piece
High strength ball bearing spindle.

Wheel Bearing Tool Set for Ford | Land Rover | Volvo
For GEN2 wheel bearings
Ford - Focus II.5RS | Focus 2.5RS 50
Ford - Mondeo MkIV from 2007
Galaxy from 2006 | S-Max from 2006 Front
Volvo S80 | V70 | XC60 | XC70 from 2006

Compact Wheel Bearing Set for Audi / VW
For removing and installing the compact wheel bearing / combined wheel hub and bearing unit on VW Polo Fox etc.
High strength spindle and components suitable for direct use on vehicle while in-situ.

Wheel Hub Bearing Unit Tool Kit
Consists of parts from 4 kits for
62 / 66 / 72 / 85mm VAG applications
CT3872 62mm Kit - Audi A2 | VW Lupo / Front
CT4275 66mm Kit - Skoda Fabia | VW Fox / Front | Polo
CT3582 72mm Kit - Audi A1 / A2 |
Seat Cordoba | Ibiza | Skoda Fabia | Roomster
VW Polo / Front | VW Fox with PAS / Front.
CT3763 85mm Kit - VW Multivan | Touareg | Transporter

90mm Audi Wheel Hub Bearing Unit Tool
For assembling and disassembling front wheel hubs.
For use with workshop hydraulic press.
Suitable for Audi A4 | A6 | A8 | R8.
Pressure Plate and Push Pins.
Disassembly shells.
Disassembly pressure piece.
Mounting sleeve

Wheel Hub and Bearing Repair Kit
Wheel Bearing Hub Removal and Repair for
Rear Wheel Drive Mercedes / Porsche and BMW.
Front Wheel Drive VAG and Asian vehicles.
The Best Kit around for rear wheel hub
and bearing servicing on German vehicles.

Wheel Hub and Bearing Service Kit
Designed to extract and install the drive flange and wheel bearing
on front and rear wheel drive vehicles where a one piece bearing is used.
Applicable to -
Rear wheel drive vehicles : BMW / Mercedes-Benz and Porsche.
Front wheel drive vehicles : Chrysler / Ford / Honda / Hyundai
Infiniti / Kia / Lexus / Mazda / Nissan / Toyota and VAG.
For use on drive axles only.

Wheel Hub and Drive Shaft Puller
4.3kg slide hammer for wheel hubs
and front-wheel drive shafts and brake drums
Suitable for most vehicles.
Bolt Size : M12 x 1.5 / M14 x 1.5

Hydraulic Wheel Hub Puller
Hydraulic Ram with 10 Ton capacity
used to press the axle shaft from the hub.
For 4 or 5 bolt hubs with a 96 - 125mm diameter circle.
Applicable to most vehicles

10T Hydraulic Wheel Hub Removal Kit
For separating the transmission shaft from the hub.
Hydraulic cylinder head - up to 10-tonne capacity.
High-pressure Hose and Five-hole Hub Axle Plate.
Extension screws : 5 x M14 x 1.5 | 5 x M12 x 1.5.
Screws : 5 x M14 x 1.25 | 5 x M14 x 1.5.
Nuts : 5 x M14 x 1.25 | 5 x M14 x 1.5.
Magnetic spacer plates.
Extension adaptor.
Quick-connect coupler.

Universal Hub Puller Kit
with Hydraulic Ram
giving up to 12 Tons of pressure
with a large Slide Hammer assembly.
Suitable for almost all 3 | 4 | 5 and 6 holed hubs.
Ideal for use on a wide range of vehicles

Wheel Hub Removal Tool
Designed to allow the easy removal of seized wheel hubs.
Covers most cars and LGV vehicles with 5 / 6 / 8 hub assemblies.
Apply the spindle to a solid point on the hub.
The spindle must put pressure on at least two solid points
on the hub to completely remove the hub.
Spindle must be lubricated before use.

Rear Hub on FWD Ford Transit Puller.
The bearings on these Transits often seize in place
requiring this special tool for removal of the hub.
2000 Front wheel drive models only

Front Wheel Bearing Puller for Ford Transit 2006 onwards
Engineered for the safe in-situ removal of the drive flange
from the bearing / hub unit when replacing brake discs.
Allows the drive flange to be split from the hub assembly and then re-used.
Puller with retaining key
Pressure plates : large / small
Spindle with hexagonal drive
Screw set - 5pc

Universal Wheel Hub Puller
200mm puller screw with striking wrench.
Fits hubs up to 250mm diameter.
For most makes and models of cars or commercial vehicles.
Revolving end of legs ensure that no damage can be done to studs
axle or inner parts of the wheel.

Hydraulic Wheel Hub Puller Set
and Ball Joint Removal Tool
Max : 10 Ton rated
Ram Length : 270mm x 38mm
Tommy bar length : 119mm
High density steel with knurled grip
Thread pitch of ram : 16 gauge x 3/8 BSW
Weight : 2kg

10 Ton Hydraulic Ram
Ball Joint Hub Bearing Puller Tool
Suitable for Cars and Vans.
Ram Length : 270mm
Width : 38mm
Tommy bar length : 119mm
Thread pitch of ram : M12 x 1.75
For use with CT0556 / CT3612 / CT3396