Digital Inclinometer
For angle measurement such as -
suspension setting of camber and caster,
setting bumper mounted radar units for vehicle collision avoidance
and parking assist systems.
Also for Citro?n / Peugeot variable valve timing setting / checking;
angle checks for comparison and setting on any flat surface.
AAA Battery included.

2pc Strut Leg Pry Socket Set
Unique shape bits
7 x 5mm | 8.2 x 5.5mm - 1/2in.Dr
Reduces risk of damage to hub casting.
Applicable to Ford | Peugeot | Renault | VAG.

Strut Clamp for Insert Pistons with 60mm Bolts
This Clamp is useful when working with Suspension Struts
that are built with strong tension stop springs
which pull the strut shaft inside the strut.
Made especially to allow the McPherson strut to extend fully.
This Kit includes 60mm long bolts.
Manufactured from anodized aluminium.

Universal Suspension Strut Split Hub Spreader
Used to remove and install suspension struts
while leaving the hub on the vehicle,
designed to keep the suspension hubs separate and open.
The double ended design can be used with the larger upper hub
and the lower ball jointed hub to be split - not easy to break.
Expertly designed to split the steering knuckle hub,
enhancing your vehicle's suspension and braking performance.

Suspension Joint Pin Socket - 1/2in.Dr
For use on castellated suspension joint nuts.
Applicable to PSA - Citroen / Peugeot Vehicles :
Citroen BX : 9 / 1982-1994
C5 Xantia
Peugeot 305 : 7 / 1982-1990 | 405 / 6 / 1987 | 406 | 605 | 607 etc.

Suspension Strut Socket - VAG
Go-Thru Socket for use with a 22mm Spanner or Socket
For loosening Audi / VW suspension strut nuts.

Suzuki Suspension Castle Nut Socket
4 Pin / 1/2in.Dr Socket
External 43mm / Internal 30.5mm
Pins : 5mm x 6.3mm
Applicable to : V650 / 1000 | DI650 / 1000 | V-Storm
Also Hayabusa / Bking and GSX-R750 / 1000 / 1100

13mm Suspension Top Mount Nut Wrench
for VAG - Audi | Seat | Skoda | VW
13mm 6 / 8 point Dual Sided Swivel Socket
120mm Total Length with 3/8in.drive.
Specialist tool designed to be used when
removing the top of Macpherson strut mounts.
Flexible for hard to reach parts allowing access
to the strut mount with minimal effort due to the flexible design.

Suspension Strut tool
Dual Size : 5 / 6mm x 182mm long.
Prevents the damper piston rod from rotating
while removing and replacing the rear strut.
Suitable for Vauxhall / Opel / Ford / VAG and Japanese vehicles.

5pc Strut Nut Tool Set
Used in conjunction with a 22mm Spanner or Socket.
Sizes - 10.5 x 3.5 | 12.5 x 3.5 | 14 x 2.5 | 14.5 x 3 | 14.5 x 5
For Macpherson front and rear struts on Audi / VW.
Holds the damper shaft during the removal of the strut nuts.

14pc Shock Absorber Tool Set
Specifically designed for repairing and replacing shock absorbers.
Go-thru Ratchet - 21mm Hex
Go-thru Deep Sockets : 16 | 17 | 18 | 19 | 21 | 22 | 24mm
Hex Bits : 6 | 7 | 8mm - 1/2in.Dr
Sliding T-Bar - 1/2in.Dr
Slot Bit Sockets : 5 x 8mm | 6 x 8mm - 1/2in.Dr
Suitable for GM / Mercedes and VAG vehicles.

19pc Shock Absorber Tool Set - 1/2in.Dr
For Automotive Suspension Spring Struts.
With 21mm Go-Thru Ratchet and Sliding T-Bar
Go-Thru Deep Sockets : 16 |17 | 18 | 19 | 21 | 22 | 24mm
120mm Oval Sockets : 5 x 8 | 6 x 8 | 7.1 x 9.6mm
120mm Hex Bits : 6 | 7 | 8mm
120mm Hex Sockets : 7 | 8 | 9mm
120mm T50 Star Bit.

43pc Turnbuckle Set for Shock Absorbers
Unique and comprehensive set of tools
for servicing spring or strut shock absorbers.
Suitable for a wide variety of vehicles
in conjunction with spring compressors.
Chrome Vanadium sockets and
Strut Nuts with 22mm hex drive.
Specialist bits with 10mm hex drive
Go-Thru Ratchet : 19 | 22mm.

Axle Backlash Tester
For localising the source of common faults around the wheel axle.
Suitable for testing under load conditions on cars up to 3.5 Tons.

Wishbone Extractor Tool
Suspension Arm Lever pushes down the suspension
for servicing the drive shaft or wheel bearing.
Total length - 1180mm
Comfortable rubber grip
Adjustable canter lever hook
Sliding adjustment for easy positioning

Universal Wishbone Lever Tool with Chain
Maximum Traction : 500kg
Total Length with Hook : 1030mm
Clamping Height : 65mm to 265mm
Chain length including hook : approx. 660mm
Enables lowering of the wishbone and holds in the retracted position.
Ideal for replacing the wheel bearing / repairing struts or drive shafts.
Prevents damage to the ball joints and drive shaft sleeves.
Low height for easy and fast assembly.

Gap Checker for Suspension and Steering
Suitable for detecting movement in worn joints, wheel bearings
and top strut mounts, recommended for use while the vehicle
is lifted with the tyres off the ground.
Securely clamps onto the wheel, providing excellent leverage
to check for play in suspension joints & wheel bearings.
For wheel diameters : 550mm to 800 mm
approx 13in. to 22in. on all popular vehicles.

3pc BMW Camber Adjustment Tool Set
For adjusting the camber of many BMW vehicles
when using a BMW KDS type alignment system.
Tool remains on the spring strut until all screws
are tightened so no recalibration required.
Suitable for BMW models - E38 to E93

VAG Camber Adjustment Tool Set
22mm Hexagonal Spindles.
3 Spindle Lengths : 75 | 85 115mm.
Pressure width 135 to 175 mm.
75mm for Seat - Toledo | VW - Jeta / Golf
85mm for Seat - Cordoba | VW - Polo / 95>
115mm for Chrysler - Voyager

2pc Coil Spring Compressor
355mm Jaw Capacity
For use On or Off vehicles when working on suspension struts
Can be use with a 1/2in.Dr Ratchet or 21mm Spanner / Socket

2pc Coil Spring Compressor
For use with 21mm socket or spanner
Total Length : 280mm
For the quick and safe removal or installation of coil springs.
Suitable for passenger cars and light duty trucks.
Heavy duty steel construction.

2pc Coil Spring Compressor Kit for MacPherson Struts
Compresses the coil spring to replace the shock absorber unit or spring.
Also allows for repairs on bent struts and strut tubes.
Forged construction threaded rod with built-in detention pins to help lock the coil in place.
Fast and easy set-up and extremely safe to use.

Heavy Duty Coil Spring Compressor with Brace
Adjustable brace to prevent accidental release of spring under load
enabling the parts of the tool used for removing the coil to always operate in parallel.
Range : 23mmm - 280mm
Capacity per pair : 1200 kg Max.
Use with a 19mm Socket or Wrench.

Heavy Duty Telescopic Coil Spring Compressor
with 100 - 185mm diameter capacity
Use with a 28mm Spanner or Impact Socket and Impact Wrench

Heavy Duty Telescopic Coil Spring Compressor
For the assembly and disassembly of MacPherson Strut Springs
at the front and rear axle of many different vehicles.
with 100 - 265mm diameter capacity
Body : 450mm long
Max. Clamp Force : 2300kg
Use with a 24mm Spanner or Impact Socket with Impact Wrench

Professional Heavy Duty Coil Spring Compressor Set
with 3 Pairs of Jaws for Macpherson Front and Rear Springs
For European and Japanese Vehicles.
Jaws Sizes : 65 -125mm | 88 -160mm | 126 - 212mm
with Robust Plastic Protectors for aftermarket springs

Telescopic Coil Spring Compressor
70 / 130mm diameter for us on most vehicles
NOT for use with Impact Drivers.

Replacement Winding Mechanism
for Coil Spring Compressor CT2614

Universal Coil Spring Compressor
Angled Jaws for wishbone multi-link suspension.
Prevents overload and Improves safety.
Suitable for most vehicles
Citroen | Peugeot | Skoda | VW

Hydraulic Coil Spring Compressor Pump
for Coil Spring Compressors : CT1321 and CT1945

Hydraulic Coil Spring Compressor
For use with 100mm to 250mm Springs
Ram Travel 340mm
Max Working Length 590mm

Coil Spring Compressor Work Station
1000kg Foot Operated Hydraulic Unit
Quicker than using ratchet driven spring compressors
Suitable for Springs from 102mm to 160mm Diameter

Coil Spring Compressor Station
1000kg Air Actuated Hydraulic Unit with Alternative Foot Operation
Quicker than using ratchet driven spring compressors
Suitable for Springs from 102mm to 160mm Diameter

Replacement Pedal
for Coil Spring Compressor Station CT1946

Hydraulic Spring Compressor Guard Cover
Steel construction with Powder Coating.
Safety guard cover prevents injury.
Suitable for : CT1321 | CT1945 | CT1946

Scania Leaf Spring Bolt Socket
3/4in.Drive
Size : 28 x 37mm
For truck servicing or repair.
Suitable for Scania leaf spring bolts on the front axle

Shock Absorber Spring Washer Socket
Size : 34 x 46mm | 3/4in.Dr
For Rear Spring Shackle Pin on Scania vehicles.
Designed for high release and tightening torques.

Shock Absorber Spring Washer Socket
Size : 34 x 56mm | 3/4in.Dr
For Rear Spring Shackle Pin on Scania vehicles.
Designed for high release and tightening torques.