Injector Copper Ring Set
Suitable for:
Deutz / Fiat / Ford / Iveco / Kia / Land Rover
MAN / Mazda / Mercedes / Renault / Universal

16pc Hex / Star / E-Socket and Bit Set
With 3/4 and 1in. Drive Adaptors plus 4mm Hex Key
Hex Bits : 17 | 19 | 22 | 24mm x 107mm Long
Star Bits : T60 | T70 | T80 | T90 | T100 x 107mm Long
E-Sockets : E18 | E20 | E22 | E24 x 107mm Long
For Truck Cylinder Head Bolts / Wheels and Shock Absorbers etc

24pc Impact Socket and Bit Set
Adaptor : 1in.Dr x 22mm Hex x 62mm long
Adaptor : 3/4in.Dr x 22mm Hex x 52mm long.
Hex Bits : 14 | 17 | 19 | 21 | 22 | 24 | 27 | 30 | 32mm
Spline Bits : M16 | M18 | M20.
Star Bits : T60 | T70 | T80 | T90 | T100
Star Sockets : E18 | E20 | E22 | E24 1/2in.Dr with 22mm Hex.
For use with impact drivers on commercial vehicles.
2.5mm Hex key for locking the bits into the driver.

6pc Impact Socket Set - 3/4in.Dr
12 point Sockets : 17 and 19mm
E-Sockets : E18 | E20 | E22 | E24
Ideal for Cylinder Head Bolts and Servicing on most Trucks

6pc 1in.Dr Shallow Impact Socket Set
Sizes : 80 | 85 | 90 | 95 | 100 | 105mm
Chrome-Molybdenum

6pc 1in.Dr Shallow Impact Socket Set
Sizes : 95 | 100 | 105 | 110 | 115 | 120mm
Chrome-Molybdenum

3/4in.Dr Torque Wrench
Range : 140 - 980Nm
With Push 'Thru' Head
Suitable for Trucks

3/4in.Dr Torque Wrench
Range : 140 - 980Nm with 8 marked settings
Reversible Ratchet with 18 Teeth
Accurate to plus or minus 4 percent
Suitable for wheel / bearing nuts / prop shaft flanges
and any extra large nut that needs accurate torque setting.

3/4in.Dr Torque Wrench
Reversible Ratchet Mechanism with 48 Teeth
Clear audible release signal.
Torque Range : 200 - 800Nm
Square Drive : 3/4in.
Accuracy : +/- 3%.
Suitable for setting torque for fasteners with right-hand thread.
Ideal for industrial and commercial vehicle applications.
Extra Long robust design in two-parts.

1in.Dr Torque Wrench
Range : 140 - 980 Nm
With Push 'Thru' Head
Suitable for Trucks

1in.Dr Torque Wrench
Range : 140 - 980 Nm with 8 marked settings
Reversible Ratchet with 18 Teeth
Accurate to plus or minus 4 percent
Suitable for wheel / bearing nuts / prop shaft flanges
and any extra large nut that needs accurate torque setting.

1in.Dr Torque Wrench
Reversible Ratchet Mechanism with 24 Teeth
Clear audible release signal.
Torque Range : 300 - 1500Nm
Square Drive : 1in.
Accuracy : +/- 3%
Suitable for setting torque for fasteners with right-hand thread.
Ideal for industrial and commercial vehicle applications.
Extra Long robust design in two-parts.

3/4in.Dr Torque Wheel Wrench
Maximum Torque : 4800Nm
Sockets : 30 | 32 | 33mm
Transmission Ratio : 68:1

1in.Dr Torque Wheel Wrench
with 38mm Socket for the installation of truck wheels
Transmission Ratio. 1.68
Maximum safe output Torque. 4800Nm

E18 Star Slogging Wrench
with 2 striking faces.
Central 20mm / 3/4in. Square Drive
For E-type fixings on commercial brake Calipers
found on front and trailing axles.
This wrench allows assembly and disassembly of the brake Calipers
without removing the steering tie rod.

E20 Star Slogging Wrench
with 2 striking faces.
Central 20mm / 3/4in. Square Drive
For E-type fixings on commercial brake Calipers
found on front and trailing axles.
This wrench allows assembly and disassembly of the brake Calipers
without removing the steering tie rod.

E24 Star Slogging Wrench
with 2 striking faces.
Central 20mm / 3/4in. Square Drive
For E-type fixings on commercial brake Calipers
found on front and trailing axles.
This wrench allows assembly and disassembly of the brake Calipers
without removing the steering tie rod.

M24 Slogging Wrench
12-point with 2 striking faces.
Central 20mm / 3/4in. Square Drive
For commercial brake Calipers on front and trailing axles.
This wrench allows assembly and disassembly of the brake Calipers
without removing the steering tie rod.

M26 Slogging Wrench
12-point with 2 striking faces.
Central 20mm / 3/4in. Square Drive
For commercial brake Calipers on front and trailing axles.
This wrench allows assembly and disassembly of the brake Calipers
without removing the steering tie rod.

Truck Injection Nozzle Socket
4 Teeth
Hex Drive : 24mm
Diameter : 22.2mm Inner | 32mm Outer
Height : 84.5mm
For use in servicing Commercial Vehicle Diesel Injectors.
on Mercdes | MAN 422 / 403 & Scania Trucks.

HGV Diesel Fuel Injector Nozzle Socket
For the removal of diesel injector nozzles on
MAN / Mercedes and Sania commercial vehicles
Use with a 22mm Spanner

Diesel Injection Valve Socket
For MAN and Mercedes Trucks
4 Tooth Socket x 72mm Deep
22mm - inside diameter
28mm - outside diameter
Applicable to : MAN 422 / 403
Mercedes Benz and Scania Trucks.

4pc Diesel Truck Injector Socket Set
70mm 4 Teeth with M14 x 1.5mm receiver thread
72mm 4 Teeth
120mm 4 Teeth
120mm 3 Teeth for injectors with electrodes

4pc Diesel Truck Injector Socket Set
for working on nozzle holders
1/2in. Dr Socket - 72mm long with 4 teeth
2 Sockets with 32mm outer hexagon and 4 teeth
1/2in.Dr Socket - 120mm long with 3 teeth

9pc Diesel Injector and Glow Plug Socket Set
1/2in.Dr Diesel Injector Sockets :
21mm x 90mm |
22mm x 78mm | 22mm x 110mm
27mm x 78mm |
28mm x 78mm | 28mm x 83mm
3/8in.Dr Glow Plug Sockets :
8 | 10 | 12mm x 158mm long with Universal Joint.

6pc Diesel Injector Extractor Set
Fuel injector puller for new generation trucks.
Applicable to trucks with injector-pump systems
or with traditional truck injectors on -
Volvo / Scania / Mercedes / MAN / Renault / IVECO.
With Socket for Delphi injectors / Injector Hook / Extension and Upper handle
Body-tamper / Universal joint / M18 x 1.5 nut.

Diesel Injector Removal Hydraulic Upgrade Kit
Providing 17 Ton Hydraulic force for diesel injector removers allowing
the controlled extraction of very tight fitting or struck injector nozzles.
Can be used in conjunction with CT3617
Hydraulic Cylinder with M16 x 1.5 Nut and Spacer Ring.
Pull Spindles M14 x 1.5 external thread - 240 / 315mm
Pull Spindles M17 x 1.0 internal thread - 240 / 315mm
Pull Spindle M18 x 1.5 internal thread - 250mm
Pull Spindle M25 x 1.0 internal thread - 240mm

Injector Nozzle Puller - Volvo HGV
Designed to aid extraction of the unit-injectors from Volvo HGV engines.
Ideal where the unit pump has overheated and stuck in the cylinder head.
Applicable to :
Volvo trucks - FM12 | FM440 | FH500
Volvo Penta marine engines - D9 | D12 | D16.
Includes slide hammer and
Puller Attachment Clamp to keep the assembly in place.

Injector Sleeve Service Set - Volvo FM Trucks
For removing or installing HGV Injector Sleeves.
Applicable to Volvo FM12 Trucks.
Contains Pre-Cutter and Removing and Mounting Tools
OEM Codes : 9998252 | 9998253 | 9998688.

Injector Sleeve Service Set - Volvo FM Trucks
For installing and removing sleeves from the cylinder head.
Sleeves need to be replaced when the truck seems powerless
and smokes with black clouds.
Two Leg Puller | Extractor Unit
Injector Sleeve / Pre-Cutter / Removal and Mounting Tools
OEM Codes : 21515329 | 88800387
9986174 | 9998252 | 9998253 | 9998688

Injector Sleeve Service Set - Volvo FM12 Trucks
For installing and removing sleeves from the cylinder head.
Sleeves need to be replaced when the truck seems powerless
and smokes with black clouds.
Two Leg Puller
Extractor Unit
Injector Sleeve Mounting Tool
OEM Codes : 88800387 | 9986174 | 9998688
Use in conjunction with sleeve installer kit - CT6715

Fuel Injector Sleeve Installation Kit
Applicable to Volvo FM12 Trucks.
For use with injector sleeve remover and installer set -
See CT6713 / CT6714
OEM Code : 21515329.

5pc Fuel Pump Water Drain Valve Plugs
For Ford 6.7 | 6.7L Diesel HFCM
Ford Truck / Pickup 2017-2022
F250 / F350 / F450 / F550 Super Duty 6.7L V8 Diesel Engines.
Easy Installation.
OEM Code : HC3Z-9J305-A

3pc Diesel Oxygen Sensor Socket Set
28mm Injector Socket 1/2in.Dr 12 point
7/8in. Injector Socket 1/2in.Dr 12 point
7/8in. Long-reach Vacuum Switch Socket
applicable to a wide range of vehicles

Engine Compression Test Kit
Compression pressure testing up to 50 bar.
Suitable for most petrol and modern HDI / TDCI
pump injector and older diesel engines.
Quick couplings for straight or angled versions.
Glow plug adaptors | Spark plug adaptors M10 / M12 / M14 and M18.
Injector adaptors M20 / M22 / M24 and stanadyne injectors
Additional pressure gauge for pressure drop test.
Suitable for most cars / trucks / buses / agricultural and marine engines.

Universal Valve Spring Compressor
For the removal and installation of valve springs on
Such as : Mitsubishi | Hino | Isuzu
With Clamping Bolt Nut : M16 x 2.0
M16 x 240mm Clamping Bolts :
M8 x 1.25 | M10 x 1.5 | M10 x 1.25 | M12 x 1.75 | M14 x 1.5
Valve Clamping Bridge and Pressure Piece

Diesel Cylinder Sleeve Puller Set
for dismantling wet cylinder liners from 60mm to 160mm.
With fully adjustable puller attachment.
For pulling off worn-out cylinder sleeves on most - motorcycles,
cars, heavy goods vehicles, agricultural engines and boats.
Not for use with power tools - hand tool use only.
Wet cylinder liners can also be found in
Vintage, Classic and Modern Engines.

Crankshaft Alignment Tool
1/2in.Drive with 2 gears
Used in conjunction with 1/2in.Dr Ratchet
Allows the engine crankshaft position to be manually rotated.
Applicable to :
MAN 12 cylinder engines and
Mercedes 6 / 8 and 10 cylinder engines.

Front Main Crankshaft Oil Seal Installer - Isuzu 3.5T
For the correct fitment of the front crankshaft oil seal
on 3.5 tonne Isuzu Truck Diesel Engines
to prevent the oil seal from damage on installation.
Vehicle applications :
N-Series trucks | D-Max and Trooper.
Engine : 4JG2 | 4JH1 - 110HP / 130HP
OEM Code seal numbers : BZ 4961E

Rear Main Crankshaft Oil Seal Installer
for Isuzu 3.5 Tonne Trucks
For correctly fitting the rear crankshaft oil seals
preventing the oil seal from damage when installing.
130 to 140 HP Engines : N-Series Trucks | D-Max | Trooper.
4JK1 / 2.5 | 4JB1 / 2.8L | 41JG1 / 3.1L | 4JH1 / 3.0L
OEM Codes : EN-50351 | 5-8840-2359-0.
Seals OEM : BZ4962-E | 8-97071-561-1

8pc HGV Cooling System Pressure Test Kit
For testing leaks in heavy goods vehicle cooling system.
Adaptors have quick-release couplings and pump is fitted with large
easy to read dial clearly marked in both psi and bar.
Quickly identifies faulty gaskets / radiators / weeping pipes
and other causes of coolant loss
Applicable to : DAF / ERF / Iveco / MAN
Renault / Mercedes-Benz / Scania / Volvo

Oil Dipstick for Mercedes Trucks
Designed to measure the transmission oil level.
Applicable : BENZ trucks.
Spring length : 860mm

9pc Oil Sump Plug Keys
Special Profile Set for assembly and disassembly of
plastic oil drain screws on plastic oil sumps.
Supplied with 3/8in.Dr T-handle or use with 17mm Socket.
For manual operation - do not use power tools.
Applicable to : Ford / PSA / BMW / VAG / Mercedes / DAF / MAN / GM.

Oil Filter Wrench - 1/2in.Dr / Chain Type
up to 120mm capacity
Double chain provides powerful and smooth operation.

32mm Ball Joint Remover
for Cars, Light Trucks and SUVs
Opening on the support fork : 32mm
Opening on the puller housing : 70mm
Max. pressure range : 92mm
Hex Drive : 26mm
Suitable for impact wrenches.

39mm Ball Joint Remover for Commercial Vehicles
For use on most trucks including - Scania / Mercedes-Benz / MAN etc.
Ideal for track rod ends and steering knuckles.
Opening on the support fork : 39mm
Opening on the puller housing : 80mm
Max. pressure range : 94mm
Hex Drive : 26mm
Chrome-Molybdenum Suitable for impact wrenches.

7pc Brake Caliper Rewind Tool Kit
For resetting brake pistons on Iveco Truck disc brakes
Suitable for Iveco Stralis / Euro cargo / Daily
With : 10mm Ratchet Wrench
Magnetic Rewind Tool with Backing Plate
Reset Discs with 2 and 3 pins
8mm Hex Bits with 10mm drive
NOTE : 2 Pin Reset Disc is 3/8in.Dr

4pc HGV Brake Caliper Socket Set
Hex 8mm | 10mm | S8 and 11PT
12mm Hex Drive
for Commercial SAF / NFZ / Knorr brake Caliper systems

Brake Caliper Socket
11pt Spline | 3/8in.Dr | 26mm Deep
For Knorr-Bremse Brake Calipers on Volvo trucks also
DAF / Foden / MAN / Mercedes / Scania / BOVA
plus BPW & SAF Trailers.

25pc Universal Press and Pull Sleeve Set
for HGV and Commercial Vehicles
such as LGVS, HGVS, Tractors etc.
Ideal for Hydraulic or Silent Bushings, Ball Bearings, Oil Seals.
Can be used with spindle and hydraulic workshop press.
Slotted sleeves allow easy view of the bearing or bushing.
Inner Sleeve Sizes : 74 - 112mm / 2mm steps.
Outer Sleeve Sizes : 84 - 122mm / 2mm steps.
Spindle Sizes : M10 x 3 / M12 x 3 / M14 x 3 / M16 x 3 / M18 x 3.

4pc Wheel Budd Internal Thread Restoring Kit
For Use on Vehicles that use Budd Wheel Nuts
M12 x 1.25 for PSA
M12 x 1.5 for BMW
M12 x 1.5 for Mercedes
M12 x 1.75 for Volvo
M14 x 1.5 for VAG Vehicles

Locating Tube for Groove Nut Sockets
Size : 46mm Inner | 52mm Outer
Practical connector system with fixing screw.
Useful for different groove socket nuts.
Enables stable work position.
Prevents slippage of the socket.
Change

Locating Tube for Groove Nut Sockets
Size : 54mm Inner | 60mm Outer
Practical connector system with fixing screw.
Useful for different groove socket nuts.
Enables stable work position.
Prevents slippage of the socket.
Change

Locating Tube for Groove Nut Sockets
Size : 60mm Inner | 67mm Outer
Practical connector system with fixing screw.
Useful for different groove socket nuts.
Enables stable work position.
Prevents slippage of the socket.
Change through loosening of the grub screw on the hexagon.

BPW Rear Hub Cap Nut Socket
Size : 95mm / Oval | 41mm Deep | 3/4in.Dr
Rear axle cover extractor socket.
Applicable to : BPW / 6.5 - 9 ton

BPW Rear Hub Cap Nut Socket
Size : 109mm / Oval | 41mm Deep | 3/4in.Dr
Rear axle cover extractor socket.
Suitable for later model of Japanese commercial trucks
tractors and other automotive industrial equipment.

BPW Rear Hub Cap Nut Socket
Size : 110mm / Oval | 41mm Deep | 3/4in.Dr
The rear axle cover extractor socket.
Applicable to : BPW / 12 ton

BPW Rear Hub Cap Nut Socket
Size : 120mm / Oval | 41mm Deep | 3/4in.Dr
Rear axle cover extractor socket.
Applicable to : BPW 13-14 ton trailer from November 2004

BPW Axle Nut Socket
65mm | 3/4in.Dr
Wrench Size : 65 x 40mm
Height : 68mm
Suitable for high tightening and release torques.
For use on special axle nuts / wheel capsules on BPW axles

BPW Axle Nut Socket
80mm | 3/4in.Dr
Wrench Size : 80 x 50mm
Height : 68mm
Suitable for high tightening and release torques.
For use on special axle nuts / wheel capsules on BPW axles.

BPW Axle Nut Socket
85mm | 3/4in.Dr
Wrench Size : 85 x 50mm
Height : 68mm
Suitable for high tightening and release torques.
For use on special axle nuts / wheel capsules on BPW axles.

BPW Axle Nut Socket
95mm | 3/4in.Dr
Wrench Size : 95 x 40mm
Height : 68mm
Suitable for high tightening and release torques.
For use on special axle nuts / wheel capsules on BPW axles.

BPW Axle Nut Socket
110mm | 3/4in.Dr
Wrench Size : 110 x 45mm
Height : 68mm
Suitable for high tightening and release torques.
For use on special axle nuts / wheel capsules on BPW axles.

BPW Axle Nut Socket
120mm | 3/4in.Dr
Wrench Size : 120 x 48.5mm
Height : 68mm
Suitable for high tightening and release torques.
For use on special axle nuts / wheel capsules on BPW axles.

BPW Axle Extractor - M125 x 2.0
For removing the wheel axle with outer thread on commercial vehicles.
Extremely robust European truck repair tool applicable to :
BPW 12 ton models.
Used in combination with 30mm and 43mm spanners
H

BPW Axle Extractor - M135 x 2.0
For removing the wheel axle with outer thread on commercial vehicles.
Extremely robust European truck repair tool applicable to :
BPW ECO 10 - 12 ton old models.
Used in combination with 30mm and 43mm sp

BPW Axle Extractor - M136 x 2.5
For removing the wheel axle with outer thread on commercial vehicles.
Extremely robust European truck repair tool applicable to :
BPW ECO Plus 8 - 12 ton
BPW ECO 10 tons new model.
Used in combinati

BPW Axle Extractor - M155 x 3.0
For removing the wheel axle with outer thread on commercial vehicles.
Extremely robust European truck repair tool applicable to :
BPW 16 ton trucks / former models.
Used in combination with 30mm and 43mm

Haldex Brake Linkage Adjuster Extractor
Allows tight brake linkage adjusters to be pulled off.
Ring shaped contact surface for a secure hold.
Hex : 32mm
Puller inside depth : 84mm
Puller inside width : 86mm
Spindle length : 9

BPW Brake Linkage Adjuster Extractor
Substantial Tool for drawing off firmly sitting BPW brake linkage adjusters.
Suitable for older and automatic linkage adjusters.
Use with 32mm wrench.
Spindle size : M22 x 1.5 x 90mm

105mm Hub Nut Socket
1in.Dr
for DAF Trucks
Drop Forged CRM

DAF Commercial Vehicle Crankshaft Alignment Tool
This heavy duty tool allows crankshaft rotation via the flywheel.
6 point drive x 24mm x 11 teeth
Applicable to 35T DAF trucks :
65CF | 75CF | 85CF | 95XF | CF75 | CF85
F65 | F75 |

DAF Engine Crankshaft Alignment Tool
1/2in. Drive
For manually rotating the engine crankshaft into position.
Applicable to : DAF XF105 / Euro5

85mm Hub Nut Socket - 1in.Dr / 12-point
for IVECO trucks and BPW / SAF trailers
Suitable for high tightening and loosening torque.
Can be used with an impact wrench or torque wrench.
Height : 60mm
External Diameter : 107.50mm

IVECO Axle Hub Nut Socket
Size : 98mm / 6 Point
Any extensive slipping is avoided.
Hex Drive: 36mm socket or spanner.
Applicable : Iveco Eurocargo and other models
For dismantling / assembly of axle nuts on commercial vehicles.

IVECO Axle Hub Nut Socket
Size : 105mm / 12 Point - across flats
Any extensive slipping is avoided.
Hex Drive: 36mm socket or spanner.
Applicable to IVECO Eurotech Cursor trucks.
For dismantling / assembly of axle nuts on commercial vehicles.

IVECO Axle Hub Nut Socket
Size : 110mm / 12 Point
Any extensive slipping is avoided.
Hex Drive: 36mm socket or spanner.
Applicable: Iveco Eurotech Cursor Ha etc
For dismantling / assembly of axle nuts on commercial vehicles.

MAN Engine Crankshaft Alignment Tool
1/2in. Drive
Length : 61mm
Allows the engine crankshaft position to be manually rotated.
Applicable to : MAN engines D20 | D25 | D26 | D28

MAN / Mercedes Crankshaft Alignment Tool
120mm Deep | 1/2in. Drive
Allows the engine crank to be manually adjusted.
Allows pinpoint accuracy calibration.
Adjusting screw in the clutch housing
Triple gear construction
Applicable to :
Mercedes Benz Actros / Atego
MAN 5-/6- and 8-cylinder engines - D25 / 28 etc.

MAN Transmission Groove Nut Socket
53.5mm | 3/4in.Dr | 4PT
For removing the transmission nut on MAN trucks.
Length : 75mm

Transmission Bearing Puller Set for Trucks
For safely and efficiently removing truck transmission bearings
on European trucks like DAF and Japanese trucks like Hino.
Compatible with 311 | 312 | 313 | 314 | 315 Series Bearings
Suitable for truck transmissions of 4 tonnes and above.
Ensures no damage to bearings or other components during removal.
Includes 5 split sleeves that securely lock into the circlip groove
on both the transmission bearings and the puller tube.
A forcing screw enables smooth bearing removal from the shaft,
centring pressure on the shaft end for proper installation.

MAN Truck Front Wheel Hub Installer
For axle bearings that are stuck due to over heating.
Can be used in conjunction with an air wrench for easier removal.
Suitable for pulling off wheel hubs with 166mm hole diameter.
Ideal European truck repair tool with extremely robust execution.
Disc size : 87 x 166 x 118mm

MAN Front Wheel Hub Tool
For Extracting / Installing wheel hubs on the front axle.
This tool makes it easier to pull out the wheel hub.
Use in conjunction with a 40mm spanner.
Inner Diameter : 50.1mm
Outer Diameter : 153.7mm

MAN Truck Axle Bearing Extractor
Inner Diameter : 107.6mm | Outer Diameter : 169mm
For removing and replacing MAN truck hub bearings.
Turn the screw and remove the old bearing.
Use with 30mm wrench
Applicable to MAN Truck Hub bearings.

MAN Truck Axle Bearing Extractor
Inner Diameter : 111mm
Outer Diameter : 169mm
Height : 240mm

For removing and replacing MAN truck hub bearings.
Use with 30mm wrench
Applicable to : MAN truck tractor 33460 / 410 / 414
with front disc brake bearing.

MAN TGA Rear Axle Extension Tube
For the removal and installation of wheel hubs.
Protects the wheel bearing and threaded bolts.
With knurling and bore for Tommy Bar.
Thread : M100 x 1.5 | Inner Size : 95mm | Outer Size : 105mm | Length: 360mm
Applicable to MAN TGA Rear Axle / HY-1350

MAN TGA Drive Shaft Nut Socket
118mm | 133mm | 3/4in.Drive | 60mm Hex
For groove nuts on MAN TGA 460 axles / V9-82L-01 / disk brake / ABS.
Designed for high tightening and release torques.
External diameter : 147.5mm
Tooth depth :

MAN TGA Front Axle Nut Socket
101mm | 110mm | 3/4in.Dr
SW60 - Six side drive
For removing the front axle nut.
Made from special steel for high tightening and loosening torque.
Overall length : 80mm
Applicable to : MAN TGA Fro

MAN / Mercedes Rear Axle Groove Nut Socket
95mm / 115mm | 3/4in. Drive
Height : 110mm
Stud width : 11.5mm
Suitable for high torque applications.
Applicable to : Mercedes / MAN - 10 / 13ton Reduction Axle
Hypoid and Trailer Ax

MAN / Mercedes Drive Axle Groove Nut Socket
101.5 x 110mm | 3/4in.Dr | 60mm Hex
With 6 teeth for removing the drive axle nut.
Suitable for high tightening and loosening torque.
Applicable to : MAN / Mercedes-Benz Trucks

MAN / Mercedes Rear Differential Nut Socket
3/4in.Dr with 6 Teeth / 8.7mm
Inner diameter : 113mm / Tooth to Tooth
Inner diameter : 126mm / Side to Side
Designed for high torque applications for
rear axle differential groove nuts o

Mercedes Axle Nut Socket
Size : 95mm / 6 Point / 157mm Long
Any extensive slipping is avoided.
Hex Drive : 36mm socket or spanner.
Applicable : Mercedes Axle Trailers

Mercedes Rear Axle Groove Nut Socket
For 6 teeth groove nuts on low-floor buses with SF portal axle AV132 -
Mercedes-Benz Citaro Bus / MAN City-Line / Neoplan / Kassbohrer
and other vehicles with identical axle.
Designed for high tight

72mm Differential Nut Socket
For loosening or tightening the castellated differential nut
used on the Mercedes-Benz Citaro and Evo Buses.
Castellated 6 Tooth Socket : 11 x 6 x 12mm deep Teeth
Outside Diameter : 84mm | Inside Diameter :

Mercedes Actros Rear Axle Groove Nut Socket
105mm | 125mm | 3/4in.Dr
Height : 180mm
Stud : 116.5mm
Stud width : 10mm
Locating tube : 60mm
Suitable for high torque applications.
Applicable to : Mercedes Benz Actros

Mercedes Benz Atego Groove Nut Socket
80mm | 95mm | 3/4in.Dr
Height : 175mm
Stud : 87mm
Stud width : 10mm
Locating tube : 49mm
Suitable for high torque applications.
Applicable to : Mercedes Benz Atego
Rear Axle / V

85mm Axle Nut Socket
For the removal of SAF Trailer Axle Nuts
Heavy Duty - prevents extensive slipping.
36mm Hex drive for use with socket or spanner.
Inside Diameter : 85mm x 82mm / Deep

140mm Axle Nut Socket
For the removal of SAF Euro Axles.
Allows repair work or visual inspection of the brake
and replacement of the wheel bearing set.
Dual Hex Drive : 32mm / 46mm for use with socket or spanner.
Inner size : 140m

Scania Transmission Rear Oil Seal Tool
For installing the transmission oil seal without causing damage.
Applicable to :
SCANIA transmission flange shafts and rear axle.
e.g. Simmer Rings part : 1 502 384 / 1 502 385

Injection Valve Cap Socket
1/2in.Dr / 8 PT / 100mm Deep
Diameter : 38mm Inner | 45mm Outer
For tightening and loosening electromagnetic injection valve caps.
Applicable to : Scania / 340 Trailer

Brake Caliper Socket
Hex : 24mm | 5 teeth
For adjusting the Calipers on brake systems from Knorr.
Applicable to : Scania / Volvo ADDB22X / SN6 / SN7 / SK7.

80mm Front Hub Nut Socket
1in.Dr | 8 Point
for Scania Trucks
Drop Forged CRM

17mm Budd Wheel Nut Socket - 1in.Dr
Square Profile
Length : 90mm
Applications : Isuzu / Mitsubishi Fuso / Hino
Chrome-Molybdenum

Budd Wheel Nut Socket
19mm - 3/4in.Dr
Length: 90mm / Square Profile
For Mitsubishi Canter, Fuso
Chrome Molybdenum

Budd Wheel Nut Socket
21mm - 3/4in.Dr
Length: 90mm / Square Profile
For Isuzu, Mitsubishi Fuso and Hino.
Chrome Molybdenum

Budd Wheel Nut Socket
20mm x 38mm - 1in.Dr
Length : 99mm / Hex profile.
For Mitsubishi Canter / Canter FE111 - Rear
Chrome Molybdenum

Budd Wheel Nut Socket
21mm x 41mm - 1in.Dr
Length : 99mm / Hex profile.
For Toyota Dyna and Dynaps 140 / Rear.
Toyota Dyna and Rino / Front.
Isuzu NPR / Front / Rear.
Chrome Molybdenum

Scania Engine Crankshaft Alignment Tool
1/2in. Drive
For manually rotating the engine crankshaft into position.
Applicable to : Scania Trucks up to 1996
OEM Code : 99309

Scania Wheel Nut Socket
113mm | 118mm | 3/4in. Drive
Special profile with 8 external studs
Removal and installation of the mounting nut on the axle bearing.
Designed for high tightening and release torques.
Applicable to : Scania

Scania Front Wheel Socket
83mm | 103mm | 1in. Drive | 8 point
Height : 74mm
For removal / fitting axle nuts in front of the brake disc
on Scania front axles / 124L / 144L
Series 4 from 96 for vehicles above 16 tons.

Scania Rear Hub Nut Socket
100mm | 123mm | 3/4in. Drive | 8 point
Height : 84mm
For positive drive of the axle nut.
Any extensive slipping is avoided.
Milled out profile.
Applicable to : SCANIA rear axle nuts

Scania Leaf Spring Bolt Socket
3/4in.Drive
Size : 28 x 37mm
For truck servicing or repair.
Suitable for Scania leaf spring bolts on the front axle

Shock Absorber Spring Washer Socket
Size : 34 x 46mm | 3/4in.Dr
For Rear Spring Shackle Pin on Scania vehicles.
Designed for high release and tightening torques.

Shock Absorber Spring Washer Socket
Size : 34 x 56mm | 3/4in.Dr
For Rear Spring Shackle Pin on Scania vehicles.
Designed for high release and tightening torques.

Axle Clamp Nut Socket
56mm | 3/4in.Dr for Commercial Vehicles.
For loosening / tightening the clamp nut on the axle stub.
Applicable to : DAF / Man / Mercedes-Benz / Kassbohrer & Setra

Axle Clamp Nut Socket
60mm | 3/4in.Dr for Commercial Vehicles.
For loosening / tightening the clamp nut on the axle stub.
Applicable to : DAF / Man / Mercedes-Benz / Kassbohrer & Setra

Volvo Crankshaft Rotating Tool
1/2in.Dr
For rotating the crankshaft on commercial vehicles via flywheel ring gear.
Applicable to : Volvo 6L and 12L.
Engines : D9A | D12 | D16C and FM 360 8x4.
OEM Code : 9996959

Brake Shoe Tool for Volvo Trucks
Required when repairing the drum brakes.
Designed for opening and fixing the brake shoe retaining spring.
Also for the dismantling and assembling of the jaw pins.
Features drive spindle for continuous opening.
Applicable to ERF E Series and EC Series :
N7 | N10 | N12 | F7 | F12 | F16 | FH12 | FH16 | FL7 | FL10
OEM Code : 9998550.

Volvo Wheel Shaft Cover Socket
for Volvo commercial vehicles.
Size : 115mm | 8 Point | 3/4in. Drive
Professional impact socket for truck repairs like
the removal of front and rear axle covers found on
Volvo commercial vehicles.
OEM Code : 9996773.

Heavy Duty Universal Joint Puller for Commercial Vehicles
For the quick and easy removal of cardan joints on drive shafts.
Puller foot opening : 65mm
Puller foot height : 8mm
Puller foot depth : 65mm
Total depth : 69mm
Clamping height : 55mm
Spindle length : 110mm
Suitable for 1in. impact wrenches

Digital Tyre Pressure Gauge for Trucks
2 Way Head design
Gauge measures 5 to 150psi / plus or minus 1psi
Gauge reads PSI / BAR and KPA
with back illumination for low light viewing

Dead Blow or Bumping Hammer
Plastic Handle with 105mm Rubber Head
Low blow-back due to steel balls in the head which
provides increased impact for loosening stuck wheel rims
when changing tyres - Heavy duty for trucks and SUVs
Handle length: 780mm
Weight : 4500g